Seiko 4R36 User Manual download pdf (Page 22)

３

To preserve the quality of your watch

A Type

Lift up the clasp to release the

buckle.

Open the ﬂ ap.

Take the pin out of the adjustment hole,

adjust the size of the strap by sliding it

back and forth, and then put the pin back

into the appropriate adjustment hole.

Close the ﬂ ap.

※Do not push the ﬂ ap in too hand.

Buckle

Flap

Moveable loop

Fixed loop

Adjustment hole

 





※ When fastening the clasp, insert the tip of the band into the movable

loop and ﬁ xed loop, and then, securely tighten the clasp.

３

To preserve the quality of your watch

There are 3 type of special clasps as described below;

If the clasp of the watch you purchased is one of them,

please refer to the indications.

$ %

Special clasps

A Type → page 85 B Type → page 86

C Type → page 88

３

To preserve the quality of your watch

● Leather band

・

A leather band is susceptible to discoloration and deterioration from moisture, sweat and direct sunlight.

・

Wipe oﬀ moisture and sweat as soon as possible by gently blotting them up with a dry cloth.

・ Do not expose the watch to direct sunlight for a long time.

・

Please take care when wearing a watch with light-colored band, as dirt is likely to show up.

・

Refrain from wearing a leather band watch other than Aqua Free bands while

bathing, swimming, and when working with water even if the watch itself is

water-resistant enforced for daily use （10- or 20-BAR water resistant）.

● Polyurethane band

・ A polyurethane band is susceptible to discoloration from light, and may be

deteriorated by solvent or atmospheric humidity.

・ Especially a translucent, white, or pale colored band easily adsorbs other

colors, resulting in color smears or discoloration.。

・ Wash out dirt in water and clean it oﬀ with a dry cloth.

（Protect the watch body from water splashes by wrapping it up in plastic wrap etc.）

・

When the band becomes less flexible, have the band replaced with a new one. If you

continue to use the band as it is, the band may develop cracks or become brittle over time.

Notes on the

length of the band

Notes on skin

irritation and allergy

Skin irritation caused by a band has various reasons such as allergy

to metals or leathers, or skin reactions against friction on dust or

the band itself.

Adjust the band to allow a little clearance with your wrist to

ensure proper airﬂ ow. When wearing the watch, leave enough

room to insert a ﬁ nger between the band and your wrist.

３

To preserve the quality of your watch

The band touches the skin directly and becomes dirty with sweat or dust.

Therefore, lack of care may accelerate deterioration of the band or cause

skin irritation or stain on the sleeve edge. The watch requires a lot of

attention for long usage.

●Metallic band

・ Moisture, sweat or soil will cause rust even on a stainless steel band if they are

left for a long time.

・ Lack of care may cause a yellowish or gold stain on the lower sleeve edge of

shirts.

・ Wipe oﬀ moisture, sweat or soil with a soft cloth as soon as possible

・ To clean the soil around the joint gaps of the band, wipe it out in water and then

brush it oﬀ with a soft toothbrush.

（Protect the watch body from water splashes by wrapping it up in plastic wrap etc.）

・ Because some titan bracelets use pins made of stainless steel, which has

outstanding strength, rust may form in the stainless steel parts.

・ If rust advances, pins may poke out or drop out, and the watch case may fall oﬀ

the bracelet, or the clasp may not open.

・ If a pin is poking out, personal injury may result. In such a case, refrain from

using the watch and request repair.

Band

1 ... 21 22 23 24 25

Comments to this Manuals

No comments

Seiko 4R36 User Manual Page 22

Comments to this Manuals

Related products and manuals for Unknown Seiko 4R36